◆ Print only
A honeycomb mesh bauble shaped like a drop, in two halves that click together, with a hanging hole at its tip.
Want your own version? Make it free in our mesh former tool. A free account gives you free downloads every week.
A drop-shaped Christmas bauble you print flat: two honeycomb nets that you warm and press into halves, then push together on the pins round the rim. It closes into a hollow drop 71 mm wide, 100 mm tall and about 70 mm deep, with a 3 mm hole at its tip for a thread, a ribbon or an ornament hook.
Made with our mesh former, the same ball press as our mesh Christmas ornament with another net. Each net prints in about 24 minutes with no supports and weighs about 6.6 g. The drop is the same on its left and right, so one press, a plug and a cavity printed once, forms the front and the back half and as many ornaments as you like.
Hang it next to the mesh ball for a mixed tree, or print a few in silk gold and purple like old glass drops. The zip has both nets, the plug, the cavity, a print sheet and the outline as an SVG for the mesh former.
Shown as a 3D render of the closed ornament in front of the press, not a photo.
Print the front net, the back net, the plug and the cavity, all flat on the bed.
Lay the front net in the cavity's pocket, flat face down, so the small locator pins go through the holes in its rim.
Warm it with the heat gun kept moving 15 to 20 cm away until it goes limp. Turn the plug over side to side, like the page of a book (its left edge goes to the right, its top stays at the top), push it straight down and hold it for a minute while it cools.
Do the same with the back net in the same press.
Put the halves rim to rim and press the printed pins of the front into the holes of the back. Thread the string through the hole at the tip.
Print details
| Type | Print only |
|---|---|
| Printed parts | 4 |
| Size (W x D x H) | 71 x 70 x 100 mm |
| Print bed needed | 108 x 79 mm, 35 mm tall |
| Filament | ~88 g |
| Layer height | 0.2 mm |
| Infill | 10% |
| Supports | Not needed |
| Download | ZIP: front and back nets + press plug + press cavity (STL) + outline (SVG) + print sheet |
| Added | 2026-11-04 |
Made with the free Mesh former generator. Upload your own drawing and get the same kind of part built from it, in your browser.
ZIP: front and back nets + press plug + press cavity (STL) + outline (SVG) + print sheet
Free for personal use. Selling the printed piece itself needs a commercial licence (Pro or Founder); passing on the file is not permitted on any plan. Full terms.
New to this? Read the mesh former guide.
Point up: the hanging hole is in the narrow tip, so the round end hangs at the bottom like a raindrop about to fall. Thread the ribbon through the hole and it hangs straight, since the drop is the same on both sides.
Yes. It is hollow and about 70 mm deep, so a coin-cell LED or a fairy light bulb fits before you close the halves. The honeycomb lets the light out on every side.
Yes. Open the mesh former and drop the SVG from the zip on it, then change the size; the depth comes down with it and the tool warns you if the net would stretch too thin. The hanging hole stays 3 mm and needs the solid tip, so keep it.
A mesh bauble whose net is a field of little stars, in two halves that click together, with a hole in the cap for the string.
A mesh bauble whose net is a field of little hearts, in two halves that click together, with a hole in the cap for the string.
A mesh bauble with an organic voronoi net, like a cell structure, in two halves that click together, with a hole in the cap for the string.
A mesh bauble with a net of diamonds like a harlequin glass ball, in two halves that click together, with a hole in the cap for the string.
A fish scale mesh bauble in two halves that click together, with a hole in the cap for the string.
A gyroid mesh bauble with the wavy pattern of 3D print infill, in two halves that click together, with a hanging hole.
A spiral mesh bauble whose net winds out from the middle, in two halves that click together, with a hanging hole.
A trihex mesh bauble of hexagons ringed by triangles, in two halves that click together, with a hanging hole.