◆ Clay
Circle polymer clay cutter set
Six round polymer clay cutters, 10 to 30 mm: stud tops, connectors and round dangles in one print.
◆ Clay
Six round polymer clay cutters, 10 to 30 mm: stud tops, connectors and round dangles in one print.
Six round cutters in the sizes earring makers use most: 10, 12 and 15 mm for studs and the small top piece of a dangle, 20, 25 and 30 mm for round drops, connectors and pendants. They are plain circles with no hole punched, because a round piece is used both ways: glue a post to the back for a stud, or pierce it where you want it for a dangle. Good for stud tops, round dangles, two and three tier earrings, charms and cabochon backs. The pieces come out 10 x 10, 12 x 12, 15 x 15, 20 x 20, 25 x 25 and 30 x 30 mm.
Made with our free cookie and clay cutter generator, not modelled by hand: we drew each shape at its size and uploaded it to the tool. The zip holds exactly what the tool gives you, one STL per cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on, printed rim down with no supports) plus each drawing as an SVG, so you can remake any of them at another size. They are cut plain, with no hole, so the back stays flat for a glued post; pierce a hole with a needle tool before baking wherever a design needs one.
For polymer clay earrings: condition Sculpey Premo or Souffle, Fimo or Cernit, roll it 2 to 3 mm thick, dust the blade with cornstarch (or cut through cling film for soft, rounded edges), press straight down and lift. Bake the pieces on a tile as your clay's packet says, for most brands 110 to 130 °C (230 to 275 °F) for 15 to 30 minutes per 6 mm, then sand the edges, varnish or add UV resin if you like, and fit jump rings, ear wires or glued posts.
The same cutters cut air-dry clay, precious metal clay, fondant and gum paste, and dough for tiny cookies, but once a cutter has touched polymer clay keep it for clay: print a second set for anything you eat.
Cut a 12 mm circle and a 25 mm circle from two different slabs and join them with a jump ring: the most sold polymer clay earring layout, from this one set.
Shown as a 3D render of the six printed cutters and the polymer clay pieces they cut, not a photo.
Print each file as exported: the rim flat on the bed, the blade pointing up, no supports.
Condition the clay until it is soft and roll it 2 to 3 mm thick on a tile or baking paper.
Dust the blade with cornstarch, or lay cling film over the clay for rounded edges.
Press the cutter straight down with a fingertip on the rim, wiggle it a little, and lift.
Pierce a hole with a needle tool where a dangle needs one.
Bake the pieces on the tile as your clay's packet says (most brands 110 to 130 °C, 15 to 30 minutes), never the cutter.
Let them cool, sand the edges, varnish if you like, and add jump rings and ear wires or glued posts.
Print details
| Works with | Clay |
|---|---|
| Printed parts | 6 |
| Print bed needed | 38 x 38 mm, 14 mm tall |
| Filament | ~10 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Not needed |
| Download | ZIP: six polymer clay cutters (6 STL) + drawings (SVG) + print and clay sheet + README |
| Added | 2026-09-26 |
Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.
Free download. Opens the Thingiverse listing in a new tab.
Free for personal use. Selling the printed piece itself needs a commercial licence (Pro or Founder); passing on the file is not permitted on any plan. Full terms.
New to this? Read the cutter guide.
Because circles are used both ways: the small ones mostly as studs with a post glued on the back, the larger ones as dangles or connectors that need one or two holes in different places. Pierce them with a needle tool before baking, where your design needs it.
Most studs are 10 to 15 mm. The 10 and 12 mm circles in this set suit small everyday studs and the top piece of a dangle, and the 15 mm circle is a bolder stud that still sits flat against the ear lobe.
Bake and sand the circles, then glue a flat pad earring post to the back with a two-part epoxy or a jewellery glue such as E6000, and let it cure fully. A dab of liquid clay under the pad before a second bake also works.
Follow your clay's packet, since brands differ: Sculpey Premo bakes at 130 °C (275 °F), Fimo and Cernit at 110 °C (230 °F), for about 30 minutes per 6 mm of thickness, and thin 2 to 3 mm earrings still get the full minimum time. Use an oven thermometer, bake on a tile, and never bake the cutter.
Yes. Every drawing is in the zip as an SVG: upload one to the free cookie and clay cutter generator, set the Cutter size slider (8 to 120 mm). The blade, rim and height stay the same at any size.
Clay
Long, thin field stones stacked without mortar, with tight dark joints. Field walls, sheep pens and farm terrain for wargaming and dioramas.
Clay
Rectangular slabs of five sizes in the Roman opus laying pattern, with narrow joints. Patios, plazas, temples and courtyards in clay.
Clay
Corrugated roofing sheets with overlapping seams, nail heads and a few dents. Shacks, sheds, barns and post-apocalyptic scrap terrain.
Clay
European four-in-one mail: rows of round rings, each through four neighbours. Armour for cosplay props, sculpts, bases and polymer clay.
Clay
Two bands of Celtic plaitwork per repeat, three strands over and under, between raised borders. For pottery, polymer clay and fondant.
Clay
A screen of round bamboo canes side by side, with nodes at staggered heights and fine fibres. Pottery, planters and Asian-style terrain.
Clay
Big dressed ashlar blocks with chiselled margins and rough, rock-faced centres. Castle keeps, city walls and fortress towers for tabletop terrain.
Clay
A broken rock face of angular blocks and flat, chipped facets. Cliffs, cave walls, rocky outcrops and mountain terrain for tabletop games.