◆ Paper

Botanical wreath embosser

A round leafy wreath with Your Text in the middle: a template for any name, date or word.

Make your own embosser Download free on Thingiverse
3D render of the printed botanical wreath embosser, open flat on its hinge, with the raised die and the matching cavity, next to a card embossed with its mark
Paper ~18 g

A full wreath of leaves in a circle, with two lines of text in an elegant serif in the middle, here reading Your Text to show where your own words go. Make it a stationery mark with your name, a date for a wedding or a birthday, or a shop name for tags and packaging. Type your words into the free embosser maker and upload the wreath as the picture.

Read more

Made with our free paper embosser maker, not modelled by hand: we drew the picture in code, uploaded it and set a 60 by 60 mm plate; the page traced it into the raised die and cut the matching cavity into the other plate. It prints as ONE part: the male die with the raised design and the female die with the matching cavity, joined by a print-in-place hinge, flat and open on the bed with no supports. Fold it shut over a card and squeeze. The design is 45 by 44 mm with a 1 mm relief. The zip holds exactly what the tool gives you, as an STL and as a 3MF with the relief as its own coloured part, plus the picture, to change and upload again.

Shown as a 3D render of the printed embosser and a card embossed with its mark, not a photo.

Botanical wreath embosser at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

2
  • Card or paper of 160 to 300 gsm: cardstock, kraft tags, envelopes or letter paper
  • About 18 g of PLA or PETG

How to use it

5

  1. Print it as exported, flat and open like a book, no supports.

  2. Once it has cooled, fold the hinge shut and open a few times to free the pin.

  3. Slide the card between the plates as far as the spot you want to emboss.

  4. Close the embosser and squeeze firmly for a second, then open it and slide the card out.

  5. For a mark that stands out, rub a little white or gold ink over the raised side.

Print details

35 minPrint time
~18 gFilament
1Printed parts
64 × 60 × 8 mmSize (W x D x H)
All print details
Print details
Works withPaper
Printed parts1
Size (W x D x H)64 x 60 x 8 mm
Print bed needed122 x 60 mm, 8 mm tall
Filament~18 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: hinged embosser (STL + coloured 3MF) + print sheet + artwork (PNG, SVG) + README
Added2026-09-28
Make your own embosser →

Made with the free Paper embosser generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Download free on Thingiverse

Free, no account needed. Opens Thingiverse in a new tab.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the embosser guide.

botanical embosserwreath embossercustom embosserpersonalized stationeryleaf wreath

Questions about this design

Why does the botanical wreath embosser say Your Text?

It is a template: it shows how a name or a word sits inside the wreath. Put your own words in with the free embosser maker, and the plates it builds are ready to print, just like the ones in this zip.

How long can the words in the botanical wreath embosser be?

Two short lines of up to about eight letters each read best inside the wreath on a 60 mm plate. Longer words get smaller, and below about 4 mm tall the letters stop embossing sharply in card.

How long does the botanical wreath embosser take to print?

About 35 minutes and 18 g of PLA on a current printer at 0.2 mm layers, as one print-in-place part. The time is estimated from the files, not sliced; at 0.12 mm layers for the crispest design it takes about half as long again.

More designs