◆ Print only
LOST AGAIN golf ball stencil
A printed cap that marks LOST AGAIN on a golf ball. Honest labelling for the long grass.
◆ Print only
A printed cap that marks LOST AGAIN on a golf ball. Honest labelling for the long grass.
Honest labelling. Whoever finds this ball in the rough will know exactly how your round went, and so will you when you find it again next week. Two lines, LOST over AGAIN: the O and the two As each keep their middle with a thin stencil bridge, so the whole cap prints as one piece.
Made with our free golf ball stencil generator, not modelled by hand: we typed LOST / AGAIN into its Initials field on two lines, chose the Bold & Blocky font and set Size to 30 mm. Everything else is the tool's default, and the STL in the zip is exactly what the tool gives you: a 71 by 48 mm cap for a standard 42.67 mm ball, with a 2.4 mm wall, 0.5 mm of clearance, a skirt that reaches 12 degrees past the middle of the ball so it cups it, and two tabs with 7 mm holes for a rubber band. Like every free download from the tool, it carries a small raised MESHCAST mark on its underside, along one tab.
Seat it on the ball, draw through the openings with a fine permanent marker, lift it off, and the joke is on the ball in under a minute. It makes a cheap, quick gift for a golfer: print the cap, mark a sleeve of balls, hand over both.
Shown as a 3D render of the printed stencil on a golf ball and a second ball with the words drawn through it, not a photo.
Print the file as exported: rim flat on the bed, dome up, with tree supports on (organic in PrusaSlicer).
Peel the supports out of the inside of the dome.
Wipe the ball clean so the ink bites, then seat the cap on top and press the rim down until it cups the ball.
Draw through each opening with short strokes from the edges inwards.
Lift the cap straight up and leave the ink for a minute before you touch it.
Print details
| Type | Print only |
|---|---|
| Printed parts | 1 |
| Size (W x D x H) | 71 x 48 x 29 mm |
| Print bed needed | 71 x 49 mm, 30 mm tall |
| Filament | ~14 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Yes |
| Download | ZIP: stencil cap (STL) + README with print settings |
| Added | 2026-09-25 |
Made with the free Golf ball stencil generator. Upload your own drawing and get the same kind of part built from it, in your browser.
Free download. Opens the Thingiverse listing in a new tab.
Free for personal use. Selling the printed piece itself needs a commercial licence (Pro or Founder); passing on the file is not permitted on any plan. Full terms.
New to this? Read the golf ball stencil guide.
From a few steps away, yes. The letters come out about 7 mm tall over the top of the ball, the same bold face as our letter stencils, so the two words read clearly when you walk up to the ball. It is a mark for finding and identifying, not for reading from the tee.
Print it as exported, rim flat on the bed and the dome up, with tree supports switched on (organic in PrusaSlicer, tree in Bambu Studio, Orca and Cura). They hold up the inside of the dome and peel out easily. Sliced in PrusaSlicer 2.7.2 at 0.2 mm layers it takes about 1 h 20 min and 14 g of PLA.
Yes. Open the free golf ball stencil generator, choose Initials and type your own words, up to two lines of six characters, and pick the Bold & Blocky font to match this one. The Ball size, Clearance and Size sliders fit a different ball or change the mark; this one uses a Size of 30 mm.
A hollow mesh ghost in two halves that snap together on printed pins, with a hanging hole on top of its head.
A puffy hollow mesh cloud in two halves that snap together on printed pins, with a hanging hole on top.
A hollow mesh mushroom in two halves that snap together on printed pins, with a hanging hole in the cap.
A dartboard stand with JOHN'S DARTS round the case, as an example of a name holder. Swap in any name for free.
A dartboard stand with DAD'S DARTS round the case: a Father's Day or birthday gift you can print tonight.
A dartboard stand with MAN CAVE round the case, for the shelf next to the board in a garage, bar or games room.
A dartboard stand with PAPA'S DARTS round the case: a grandpa or dad gift you can print in an afternoon.
A dartboard stand with GAME ROOM round the case, for the shelf by the board, the pool table or the console.