◆ Print only

WORM BURNER golf ball stencil

A printed cap that marks a worm over BURNER on a golf ball, for the drive that never leaves the ground.

Make your own golf ball stencil
3D render of an orange 3D-printed golf ball stencil with a worm over BURNER cut through it, sitting on a golf ball, next to a ball marked with a worm over BURNER in red
Print only ~15 g Pro early access

A picture puzzle for the topped drive that scuttles along the grass at head height for a worm: a wriggling worm over the word BURNER, so the ball reads WORM BURNER. The worm is cut in segments with thin plastic rings between them, which is what makes it read as a worm and keeps the cap in one piece; only the middles of the B and the two Rs need thin stencil bridges.

Read more

Made with our free golf ball stencil generator, not modelled by hand: we drew a worm over BURNER as an SVG, the word set in the tool's own Bold & Blocky outlines, chose Upload under Design from, loaded the file and set Size to 32 mm (the SVG is in the zip). Everything else is the tool's default, and the STL in the zip is exactly what the tool gives you: a 71 by 48 mm cap for a standard 42.67 mm ball, with a 2.4 mm wall, 0.5 mm of clearance, a skirt that reaches 12 degrees past the middle of the ball so it cups it, and two tabs with 7 mm holes for a rubber band. Like every free download from the tool, it carries a small raised MESHCAST mark on its underside, along one tab.

Seat it on the ball, draw through the openings with a fine permanent marker, lift it off, and the joke is on the ball in under a minute. It makes a cheap, quick gift for a golfer: print the cap, mark a sleeve of balls, hand over both.

Shown as a 3D render of the printed stencil on a golf ball and a second ball with the words drawn through it, not a photo.

WORM BURNER golf ball stencil at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • A standard golf ball, 42.67 mm
  • A fine permanent marker (the letters are small, a chisel tip is too broad)
  • About 15 g of PLA or PETG
  • A rubber band, if you want to hold the cap on through the tab holes

How to make it

5

  1. Print the file as exported: rim flat on the bed, dome up, with tree supports on (organic in PrusaSlicer).

  2. Peel the supports out of the inside of the dome.

  3. Wipe the ball clean so the ink bites, then seat the cap on top and press the rim down until it cups the ball.

  4. Draw through each opening with short strokes from the edges inwards.

  5. Lift the cap straight up and leave the ink for a minute before you touch it.

Print details

1 h 20 minPrint time
~15 gFilament
1Printed parts
71 × 48 × 29 mmSize (W x D x H)
All print details
Print details
TypePrint only
Printed parts1
Size (W x D x H)71 x 48 x 29 mm
Print bed needed71 x 49 mm, 30 mm tall
Filament~15 g
Layer height0.2 mm
Infill15%
SupportsYes
DownloadZIP: stencil cap (STL) + artwork (SVG) + README with print settings
Added2026-09-27

Pro early access until October 27, 2026, then free with any account.

Like it or post your print on Thingiverse

Make your own golf ball stencil →

Made with the free Golf ball stencil generator. Upload your own drawing and get the same kind of part built from it, in your browser.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the golf ball stencil guide.

worm burner golf ballfunny golf ball stencilgolf slang giftgolf ball icon stencilgolf ball stencil stl

Questions about this design

What does WORM BURNER mean on the WORM BURNER golf ball stencil?

A worm burner is a shot hit so low that it skims along the grass, close enough to singe any worm in its path. Most golfers have hit one off the first tee with everyone watching, which is exactly who this ball is for.

How do I print the WORM BURNER golf ball stencil?

Print it as exported, rim flat on the bed and the dome up, with tree supports switched on (organic in PrusaSlicer, tree in Bambu Studio, Orca and Cura). They hold up the inside of the dome and peel out easily. At 0.2 mm layers and MK3-class speeds it takes about 1 h 20 min and 15 g of PLA (estimated from the file, not sliced); a current printer is faster.

Can I change the picture or the word on the WORM BURNER golf ball stencil?

Yes. The zip carries the artwork as an SVG of plain outlines: change the word or the picture in any vector editor, then open the free golf ball stencil generator, choose Upload and load your file. It cuts whatever you draw and ties any loose middle back on with a bridge; this one uses a Size of 32 mm.

More designs