◆ Cookie dough

Easter cookie cutter set with stamps

Five Easter cookie cutters with stamps: a decorated egg, bunny, hatching chick, carrot and tulip.

Make your own cookie cutter
3D render of five 3D-printed Easter cookie cutters with their stamps and a golden stamped cookie in front of each: Easter egg, bunny, hatching chick, carrot and tulip
Cookie dough ~88 g Pro early access

Five spring shapes for the Easter table: an egg with a zigzag band, dots and a wave, a bunny face with long ears, a chick hatching out of its shell, a carrot with its leafy top and a tulip on its stem. Every cutter has a stamp that presses the pattern, the face or the petals into the cookie. Good for Easter baskets, egg hunts, spring bake sales, Easter brunch and kids' decorating afternoons.

Read more

All five were made with our free cookie cutter generator, not modelled by hand: we drew each shape with its stamp's lines inside it and uploaded it with Generate stamp switched on. The zip holds exactly what the tool gives you, one STL per shape with the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and its stamp side by side, plus each drawing as an SVG. The cookies come out 68 x 85 mm (Easter egg), 58 x 90 mm (bunny), 69 x 85 mm (hatching chick), 60 x 85 mm (carrot) and 54 x 90 mm (tulip).

Let children decorate: the pressed lines on the egg and the chick keep each colour in its own section, so even a wobbly hand turns out a neat cookie. Pastel icing and sprinkles are all you need.

The cutters and stamps print flat with no supports, in PLA or PETG. A cutter touches dough for a minute, but a 3D print has fine layer grooves where crumbs can sit: pick a food-contact filament if you can, wash each part by hand in warm soapy water before and after use, never in a dishwasher, and flour the blade and stamp before every press.

Shown as a 3D render of the five printed cutters, their stamps and a stamped cookie from each, not a photo.

Easter cookie cutter set with stamps at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutters and the stamps, and baking paper
  • About 88 g of PLA or PETG for the whole set, ideally a food-contact filament

How to use it

7

  1. Print each file as exported: the cutter rim flat on the bed with the blade pointing up, and its stamp beside it, no supports.

  2. Wash every part in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip a cutter's blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust its stamp, press it into each cookie that cutter cut, about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash the parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

9 h 20 minPrint time
~88 gFilament
10Printed parts
All print details
Print details
Works withCookie dough
Printed parts10
Print bed needed178 x 98 mm, 14 mm tall
Filament~88 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: five cutters with their stamps (5 STL) + print and food-contact sheet + drawings (SVG) + README
Added2026-09-27

Pro early access until October 27, 2026, then free with any account.

Like it or post your print on Thingiverse

Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the cutter guide.

easter cookie cutter seteaster cookie cuttersbunny cookie cuttereaster egg cookie cuttercookie cutter and stamp set

Questions about this design

What shapes are in the Easter cookie cutter set?

Five, each with its own stamp: a decorated Easter egg, a bunny face, a chick hatching from its egg, a carrot and a tulip. The stamps press in the egg's bands and zigzag, the bunny's face, the cracked shell and the petals.

Are the Easter cookie cutters easy for children to use?

Yes: the rim on top gives small hands a wide, flat place to press, and the shapes have no thin parts that tear. Let the children cut and stamp, then bake; the stamped lines make icing easy too.

Can I hang the Easter egg cookies from the Easter cookie cutter set on an Easter tree?

Yes. Push a drinking straw through the top of each egg before baking, bake them until crisp right through, and thread a ribbon once they are cold and iced. Crisp cookies hang for several days on a branch.

Can I make the cutters in the Easter cookie cutter set bigger or smaller?

Yes. Every drawing is in the zip as an SVG: upload one to the free cookie cutter generator, switch on Generate stamp and move the Cutter size slider (these are 85 to 90 mm). The stamp scales with its cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →