◆ Soap
Emotional support soap mold
EMOTIONAL SUPPORT SOAP in raised letters on a 90 mm bar, as a silicone mold from printed parts.
◆ Soap
EMOTIONAL SUPPORT SOAP in raised letters on a 90 mm bar, as a silicone mold from printed parts.
A soap bar 90 x 62 mm and about 22 mm thick with a raised border and three lines of bold raised letters: EMOTIONAL SUPPORT SOAP, with SOAP set larger.
Made with the box mode of our silicone mold maker in its rectangular shape: print the base with the soap master fused onto it face up, the two walls and the clamps, pour about 337 ml of silicone, and the block you get casts the bar face down, so the lettering comes out on the show face and the back stays flat.
A joke bar that sells itself as a gift for a colleague, a new parent or anyone having a week. Pour it in a calm pastel with lavender or chamomile, or pour the letters a darker shade first so the words stand out. The zip carries every printed part, the soap master as its own STL, the tool's own print-settings sheet and a recipe file for the generator.
Shown as a 3D render of the printed mold parts pulled apart around the master, not a photo.
Print the base with the master fused onto it, the two walls and the two clamps.
Stand the walls on the base, slide the clamps over the corners, and seal the outside seams with tape or hot glue.
Put a steel binder clip over each pair of small tabs at the foot of the walls (one tab on the wall, one on the base) so the walls cannot lift while the silicone cures.
Mix 369 ml of silicone in one batch and pour it into a corner, letting it rise around the master until it covers the top.
Once it has cured, take the clamps and walls off and pull the silicone block off the master. That block is your mold.
Turn the block over. Pour melt-and-pour soap at 55 to 60 C, spray the surface with alcohol to pop the bubbles, and let it set for a few hours.
Flex the silicone and push the bar out from the back. The letters read the right way round on the finished bar.
Print details
| Cast material | Soap |
|---|---|
| Printed parts | 5 |
| Size (W x D x H) | 152 x 108 x 56 mm |
| Print bed needed | 152 x 108 mm, 57 mm tall |
| Filament | ~207 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Not needed |
| Download | ZIP: 5 printed parts (STL) + soap bar master (STL) + print sheet + recipe |
| Added | 2026-09-25 |
Pro early access until October 25, 2026, then free with any account.
Make your own silicone mold →Made with the free Silicone mold maker generator. Upload your own model and get the same kind of mold built around it, in your browser.
Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.
New to casting? Read the silicone mold maker guide.
Pour the finished bar in one colour, let it set, then brush a little mica mixed with rubbing alcohol over the raised letters only, or rub a soap-safe colour into them and wipe the flat face clean.
This file has the text built in. For your own words, upload any bar with your text to our silicone mold maker, or make the lettering with the text sign designer first and use that as the master.
Calming ones: lavender, chamomile, vanilla or a soft cotton scent. It is a gift bar, so a gentle base and a mild fragrance keep it suitable for most people.
SoapPro early access
A 78 mm lemon slice soap bar with the rind, segments and pips on its face, as a silicone mold from printed parts.
SoapPro early access
Four snowflake soaps with ridged arms and a raised centre, poured straight into a printed tray.
SoapPro early access
A brain-shaped soap bar for a proper brainwash: 90 mm, folds and all, as a silicone mold from printed parts.
SoapPro early access
A slice of toast that smiles back: an 80 mm soap bar with crust, eyes and rosy cheeks, from a silicone mold you print.
SoapPro early access
A giant chicken nugget with a bite taken out, as an 87 mm soap bar from a silicone mold you print.
SoapPro early access
A grinning frog face soap, 84 mm wide with big bulging eyes, from a silicone mold you print.
SoapPro early access
An 88 mm soap bar with a rippled face, as a silicone mold from a printed box.
SoapPro early access
Six scallop shell guest soaps from one silicone tray, ribs and hinge included.