◆ Cookie dough

Farm animal cookie cutter set with stamps

Six farm cookie cutters with stamps: cow, pig, hen, sheep, red barn and tractor.

Make your own cookie cutter
3D render of six 3D-printed farm animal cookie cutters with their stamps and a golden stamped cookie in front of each: cow, pig, hen, sheep, barn and tractor
Cookie dough ~141 g Pro early access

Six farmyard shapes for a barnyard party: a cow's face with horns and a patch, a round pig's face with its snout, a hen with a red comb, a woolly sheep, a barn with a hayloft and cross-braced doors, and a tractor with a big back wheel. Every cutter has a stamp that presses the faces, the wool curls, the doors or the wheel hubs into the cut cookie. Good for farm and barnyard birthdays, first birthdays, baby showers, harvest festivals and school farm visits.

Read more

All six were made with our free cookie cutter generator, not modelled by hand: we drew each shape with its stamp's lines inside it and uploaded it with Generate stamp switched on. The zip holds exactly what the tool gives you, one STL per shape with the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and its stamp side by side, plus each drawing as an SVG. The cookies come out 86 x 90 mm (cow), 79 x 90 mm (pig), 90 x 87 mm (hen), 90 x 80 mm (sheep), 86 x 90 mm (barn) and 88 x 90 mm (tractor).

For a woolly sheep, pipe small blobs of white royal icing all over the body and leave the face and legs bare; for the cow, flood it white and add black patches with a spoon before the icing sets, so they flow in flat.

The cutters and stamps print flat with no supports, in PLA or PETG. A cutter touches dough for a minute, but a 3D print has fine layer grooves where crumbs can sit: pick a food-contact filament if you can, wash each part by hand in warm soapy water before and after use, never in a dishwasher, and flour the blade and stamp before every press.

Shown as a 3D render of the six printed cutters, their stamps and a stamped cookie from each, not a photo.

Farm animal cookie cutter set with stamps at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutters and the stamps, and baking paper
  • About 141 g of PLA or PETG for the whole set, ideally a food-contact filament

How to use it

7

  1. Print each file as exported: the cutter rim flat on the bed with the blade pointing up, and its stamp beside it, no supports.

  2. Wash every part in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip a cutter's blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust its stamp, press it into each cookie that cutter cut, about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash the parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

15 h 5 minPrint time
~141 gFilament
12Printed parts
All print details
Print details
Works withCookie dough
Printed parts12
Print bed needed204 x 98 mm, 14 mm tall
Filament~141 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: six cutters with their stamps (6 STL) + print and food-contact sheet + drawings (SVG) + README
Added2026-09-28

Pro early access until October 28, 2026, then free with any account.

Like it or post your print on Thingiverse

Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the cutter guide.

farm animal cookie cutter setfarm cookie cuttersbarnyard cookie cutterscow cookie cuttertractor cookie cutter

Questions about this design

Which shapes are in the farm animal cookie cutter set?

Six, each with a matching stamp: a cow, a pig, a hen, a sheep, a red barn and a tractor. The stamps press in the faces and snouts, the hen's wing, the sheep's curls, the barn doors and hayloft and the tractor's wheel hubs and cab window.

Are the farm animal cookie cutters good for a first birthday?

Yes, the shapes are big and chunky, with no thin legs or ears that snap off, so they suit little hands and teething-friendly plain biscuits too. Bake them a little thicker, about 6 mm, and skip the icing for the smallest guests.

How do I colour the farm animal cookie cutter set without piping skills?

Flood each cookie in one colour, pink for the pig, white for the sheep, red for the barn, and let it crust. Then fill only the pressed grooves with black or dark brown icing from a small bag: the stamp has already drawn every face and door.

Can I make the cutters in the farm animal cookie cutter set bigger or smaller?

Yes. Every drawing is in the zip as an SVG: upload one to the free cookie cutter generator, switch on Generate stamp and move the Cutter size slider (these are 90 mm). The stamp scales with its cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →