◆ Cookie dough

Halloween cookie cutter set with stamps

Six Halloween cookie cutters, each with a stamp: jack-o'-lantern, ghost, bat, witch hat, cauldron and candy corn.

Make your own cookie cutter
3D render of six 3D-printed Halloween cookie cutters with their stamps and a golden stamped cookie in front of each: jack-o'-lantern, ghost, bat, witch hat, cauldron and candy corn
Cookie dough ~112 g Pro early access

Six Halloween shapes in one download: a grinning jack-o'-lantern, a waving ghost, a bat with its wings out, a witch hat with a buckled band, a bubbling cauldron and a piece of candy corn. Every cutter has a stamp that drops inside it and presses the face, the band or the stripes into the cut cookie, so the whole tray is decorated before any icing. Good for Halloween parties, trick-or-treat bags, school bake sales and spooky cookie boxes.

Read more

All six were made with our free cookie cutter generator, not modelled by hand: we drew each shape with its stamp's lines inside it and uploaded it with Generate stamp switched on. The zip holds exactly what the tool gives you, one STL per shape with the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and its stamp side by side, plus each drawing as an SVG. The cookies come out 85 x 82 mm (jack-o'-lantern), 85 x 79 mm (ghost), 90 x 45 mm (bat), 85 x 80 mm (witch hat), 85 x 85 mm (cauldron) and 56 x 80 mm (candy corn).

Use the stamped lines as colouring guides: orange and black for the pumpkin, white for the ghost, purple and green for the hat and cauldron, and the three candy corn stripes in yellow, orange and white.

The cutters and stamps print flat with no supports, in PLA or PETG. A cutter touches dough for a minute, but a 3D print has fine layer grooves where crumbs can sit: pick a food-contact filament if you can, wash each part by hand in warm soapy water before and after use, never in a dishwasher, and flour the blade and stamp before every press.

Shown as a 3D render of the six printed cutters, their stamps and a stamped cookie from each, not a photo.

Halloween cookie cutter set with stamps at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutters and the stamps, and baking paper
  • About 112 g of PLA or PETG for the whole set, ideally a food-contact filament

How to use it

7

  1. Print each file as exported: the cutter rim flat on the bed with the blade pointing up, and its stamp beside it, no supports.

  2. Wash every part in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip a cutter's blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust its stamp, press it into each cookie that cutter cut, about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash the parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

12 hPrint time
~112 gFilament
12Printed parts
All print details
Print details
Works withCookie dough
Printed parts12
Print bed needed204 x 93 mm, 14 mm tall
Filament~112 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: six cutters with their stamps (6 STL) + print and food-contact sheet + drawings (SVG) + README
Added2026-09-27

Pro early access until October 27, 2026, then free with any account.

Like it or post your print on Thingiverse

Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the cutter guide.

halloween cookie cutter sethalloween cookie cutterspumpkin cookie cutterghost cookie cuttercookie cutter and stamp set

Questions about this design

Which shapes are in the Halloween cookie cutter set?

Six: a jack-o'-lantern with its face, a ghost with eyes and an open mouth, a bat, a witch hat with a buckle, a cauldron with bubbles and a candy corn with its stripes. Each has its own stamp for the lines inside it.

How do I ice the Halloween cookie cutter set cookies quickly?

Flood each cookie in its base colour and let it crust, then fill the pressed grooves with black or white icing from a fine tip. The stamp has already drawn the faces and stripes, so nobody has to pipe a face freehand.

Can I print the Halloween cookie cutter set in time for this Halloween?

Yes. Each cutter with its stamp is one plate of about two hours at the speeds on this page, less on a fast current printer, so two or three a night finish the six within a few days. Wash them and they are ready to use.

Can I make the cutters in the Halloween cookie cutter set bigger or smaller?

Yes. Every drawing is in the zip as an SVG: upload one to the free cookie cutter generator, switch on Generate stamp and move the Cutter size slider (these are 80 to 90 mm). The stamp scales with its cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →