◆ Concrete
Leaf incense holder mold
A 116 mm leaf incense holder with pressed-in veins and a stick hole, to cast in concrete, as a silicone mold.
◆ Concrete
A 116 mm leaf incense holder with pressed-in veins and a stick hole, to cast in concrete, as a silicone mold.
An incense holder in the shape of a leaf, 116 mm long and 48 mm wide: a flat, gently domed leaf with a midrib and five pairs of veins pressed into the top, and a rounded knob at the stem end holding a 3.2 mm hole for a stick, angled so the stick leans out over the leaf and the ash lands on it.
Made with the box mode of our silicone mold maker in its contoured shape, which follows the leaf and saves silicone: print the base with the leaf fused onto it, the walls and the clamps, pour about 383 ml of silicone, and the silicone forms the stick hole as a pin. Turn the block over and cast the leaf through its flat back.
Cast them in grey concrete, charcoal-tinted Jesmonite or white plaster for a calm, natural look, and sell them in sets with a pack of incense. The zip carries every printed part, the leaf master as its own STL, the tool's own print-settings sheet and a recipe file for the generator.
Shown as a 3D render of the printed mold parts pulled apart around the master, not a photo.
Print the base with the master fused onto it, the two walls and the two clamps.
Stand the walls on the base, slide the clamps over the corners, and seal the outside seams with tape or hot glue.
Mix 417 ml of silicone in one batch and pour it into a corner, letting it rise around the master until it covers the top.
Once it has cured, take the clamps and walls off and pull the silicone block off the master. That block is your mold.
Turn the block over: the opening is the back of the leaf. Fill it with a fine concrete mix or Jesmonite, tap the sides to raise the air, and strike the back flat.
Demold after a day, sand the back flat and seal the leaf so the ash wipes off.
Print details
| Cast material | Concrete |
|---|---|
| Printed parts | 5 |
| Size (W x D x H) | 166 x 71 x 51 mm |
| Print bed needed | 167 x 71 mm, 51 mm tall |
| Filament | ~137 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Not needed |
| Download | ZIP: 5 printed parts (STL) + incense holder master (STL) + print sheet + recipe |
| Added | 2026-09-25 |
Pro early access until October 25, 2026, then free with any account.
Make your own silicone mold →Made with the free Silicone mold maker generator. Upload your own model and get the same kind of mold built around it, in your browser.
Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.
New to casting? Read the silicone mold maker guide.
The hole is 3.2 mm across, which takes the bamboo core of standard stick incense and most thin sticks. It is angled so the stick leans out over the leaf, and the leaf is long enough to catch the ash of a normal 25 cm stick.
Yes. The silicone forms the hole as a thin pin, so fill round it gently with a fine mix and tap the mold rather than stirring near it. If a little concrete skins over the top of the hole, a 3 mm drill bit turned by hand clears it.
Yes, and resin shows the veins beautifully. Use a heat-resistant casting resin, since the end of a stick can touch the leaf, and add a little mica or a few dried petals near the tip for a botanical look.
Pro early access
Concrete
A 100 mm scalloped trinket dish to cast in concrete or Jesmonite, as a silicone mold from printed parts.
Pro early access
Concrete
A 100 mm hexagon coaster with three nested grooves, as an open-face silicone mold.
Pro early access
Concrete
A fluted concrete tealight holder, 78 mm across, as a silicone mold from printed parts.
Pro early access
Concrete
Two concrete soap dishes with a rim and drain ridges, cast straight in a printed tray.
Pro early access
Concrete
Four round concrete coasters with ripple grooves, cast straight into a printed tray.
Pro early access
Concrete
Four square art deco coasters with a sunburst in the face, cast in a printed tray.
Pro early access
Concrete
Cast a 140 mm classical male torso in concrete or plaster. Silicone mold kit.
Concrete
Reusable two-part mold with an inner core. Cast a ribbed vase or planter in concrete.