◆ Cookie dough

Reindeer cookie cutter and stamp

A reindeer head with chunky antlers, and a stamp that presses in the eyes, ears and a big round nose.

Make your own cookie cutter Download free on Thingiverse
3D render of a brown 3D-printed reindeer cookie cutter and stamp next to two golden baked cookies with the eyes, ears and a round nose pressed in
Cookie dough ~25 g

A cheerful reindeer face seen from the front, with chunky antlers, two ears and a long muzzle. The stamp presses in a border line, the eyes, a line in each ear and a big round nose that is just asking for red icing. Good for cookies for the reindeer on Christmas Eve, class parties, Christmas cookie boxes and winter birthdays. The cookie comes out about 84 by 95 mm.

Read more

Made with our free cookie cutter generator, not modelled by hand: we drew the shape with the stamp's lines inside it, uploaded it to the tool, set the cutter size to 95 mm and switched on Generate stamp. The STL in the zip is exactly what the tool gives you: the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and, next to it, the stamp that drops inside the cutter and presses the lines into the cut cookie. Both print flat, with no supports. The drawing is in the zip too, as an SVG, so you can make both bigger or smaller.

Fill the pressed nose with red icing, or push a red sugar-coated chocolate into it straight out of the oven while the cookie is still soft. It sets in place as the cookie cools.

Shown as a 3D render of the printed cutter and stamp and two stamped cookies, not a photo.

Reindeer cookie cutter and stamp at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutter and the stamp, and baking paper
  • About 25 g of PLA or PETG, ideally a food-contact filament

How to use it

7

  1. Print the file as exported: the cutter rim flat on the bed with the blade pointing up, and the stamp beside it, no supports.

  2. Wash both parts in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip the blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust the stamp, press it pattern side down into each cut cookie about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash both parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

2 h 40 minPrint time
~25 gFilament
2Printed parts
203 × 103 × 14 mmSize (W x D x H)
All print details
Print details
Works withCookie dough
Printed parts2
Size (W x D x H)203 x 103 x 14 mm
Print bed needed203 x 103 mm, 14 mm tall
Filament~25 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: cutter and stamp (STL) + print and food-contact sheet + silhouette (SVG) + README
Added2026-09-26
Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Download free on Thingiverse

Free download. Opens the Thingiverse listing in a new tab.

Free for personal use. Selling the printed piece itself needs a commercial licence (Pro or Founder); passing on the file is not permitted on any plan. Full terms.

Food contact: the cutter only touches dough briefly, but layer lines hold residue. Print it in a food-contact filament, wash it by hand in warm water, and keep it away from the dishwasher. Food-safe guide.

New to this? Read the cutter guide.

reindeer cookie cutterreindeer cookie stampchristmas reindeer cookiechristmas cookie cutter and stamp

Questions about this design

Will the antlers on the reindeer cookie break when I lift it?

The antlers are drawn thick for exactly this reason, about 12 mm wide on the cookie. Chill the cut dough for ten minutes, bake until the edges only just colour, and let the reindeer cool on the tray before you move them.

How do I decorate the reindeer cookies quickly?

Leave the dough plain or flood the face in light brown, fill the pressed nose with red and the eyes with dark chocolate or black icing. The stamp has already drawn every line, so children can do the rest themselves.

Can I make the reindeer cutter bigger or smaller?

Yes. Upload reindeer.svg from the zip to the free cookie cutter generator, switch on Generate stamp, and move the Cutter size slider (this one is 95 mm). The stamp scales with the cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →