◆ Cookie dough

Santa hat cookie cutter and stamp

A floppy Santa hat with a fur brim and a pompom, and a stamp that presses in the brim and the fur.

Make your own cookie cutter Download free on Thingiverse
3D render of a red 3D-printed Santa hat cookie cutter and stamp next to two golden baked cookies with the fur brim and the pompom pressed in
Cookie dough ~21 g

Santa's hat, flopping to one side, with a thick fur brim along the bottom and a big pompom on the tip. The stamp presses a border line, the edge of the brim, a row of dots for the fur and a ring round the pompom. Good for Christmas parties, school Christmas fairs, Christmas cookie boxes and cupcake toppers. The cookie comes out about 90 by 75 mm.

Read more

Made with our free cookie cutter generator, not modelled by hand: we drew the shape with the stamp's lines inside it, uploaded it to the tool, set the cutter size to 90 mm and switched on Generate stamp. The STL in the zip is exactly what the tool gives you: the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and, next to it, the stamp that drops inside the cutter and presses the lines into the cut cookie. Both print flat, with no supports. The drawing is in the zip too, as an SVG, so you can make both bigger or smaller.

For a fluffy brim and pompom, pipe thick white royal icing and sprinkle white sanding sugar or desiccated coconut over it while it is wet. Flood the red part first and let it crust.

Shown as a 3D render of the printed cutter and stamp and two stamped cookies, not a photo.

Santa hat cookie cutter and stamp at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutter and the stamp, and baking paper
  • About 21 g of PLA or PETG, ideally a food-contact filament

How to use it

7

  1. Print the file as exported: the cutter rim flat on the bed with the blade pointing up, and the stamp beside it, no supports.

  2. Wash both parts in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip the blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust the stamp, press it pattern side down into each cut cookie about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash both parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

2 h 20 minPrint time
~21 gFilament
2Printed parts
203 × 83 × 14 mmSize (W x D x H)
All print details
Print details
Works withCookie dough
Printed parts2
Size (W x D x H)203 x 83 x 14 mm
Print bed needed204 x 84 mm, 14 mm tall
Filament~21 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: cutter and stamp (STL) + print and food-contact sheet + silhouette (SVG) + README
Added2026-09-26
Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Download free on Thingiverse

Free download. Opens the Thingiverse listing in a new tab.

Free for personal use. Selling the printed piece itself needs a commercial licence (Pro or Founder); passing on the file is not permitted on any plan. Full terms.

Food contact: the cutter only touches dough briefly, but layer lines hold residue. Print it in a food-contact filament, wash it by hand in warm water, and keep it away from the dishwasher. Food-safe guide.

New to this? Read the cutter guide.

santa hat cookie cutterchristmas hat cookie cuttersanta hat cookie stampchristmas cookie cutter and stamp

Questions about this design

How do I make the fur on the Santa hat cookies look fluffy?

Pipe the brim and the pompom in stiff white royal icing and dab it with a clean dry brush while it is wet, or press white sanding sugar or desiccated coconut into it. The pressed dots under it keep a hint of texture.

Can I put the Santa hat cookies on cupcakes?

Yes. Roll the dough 4 to 5 mm thick so the hats are light enough to lie on top of the frosting. Push a cocktail stick into the brim before baking if you want them to stand up in the swirl instead.

Can I make the Santa hat cutter bigger or smaller?

Yes. Upload santa-hat.svg from the zip to the free cookie cutter generator, switch on Generate stamp, and move the Cutter size slider (this one is 90 mm). The stamp scales with the cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →