◆ Concrete
Scalloped concrete trinket dish mold
A 100 mm scalloped trinket dish to cast in concrete or Jesmonite, as a silicone mold from printed parts.
◆ Concrete
A 100 mm scalloped trinket dish to cast in concrete or Jesmonite, as a silicone mold from printed parts.
A round trinket dish 100 mm across and 24 mm tall: eight soft scallops round a thick, rounded rim, walls that flare out a little, and a well 18 mm deep with a rounded inside edge. Rings, keys, a soap bar or a tealight all fit.
Made with the box mode of our silicone mold maker in its round shape: print the base with the dish fused onto it upright, the walls and the clamps, pour about 513 ml of silicone, and the silicone fills the well as it rises. Turn the block over and the dish casts upside down, its flat bottom as the open face you fill.
Cast a stack in grey concrete, white Jesmonite or terrazzo with coloured chips, and seal them for a shop shelf or a market table. The zip carries every printed part, the dish master as its own STL, the tool's own print-settings sheet and a recipe file for the generator.
The main photo is our own test print: the dish fused on its round base and one blue wall, straight off a Bambu textured plate. The second image is a 3D render of every part, clamps included.
Print the base with the master fused onto it, the two walls and the two clamps.
Stand the base on the table. Set each wall down a few centimetres out from it and slide it in over the table until the ridge round the base sits in the groove at its foot, then slide the clamps down over the seams. Once they are on, the walls cannot lift, and the ridge seals the bottom.
Mix 554 ml of silicone in one batch and pour it into a corner, letting it rise around the master until it covers the top.
Once it has cured, take the clamps off, slide the walls straight out and pull the silicone block off the master. That block is your mold.
Turn the block over: the opening is the bottom of the dish. Fill it with a fine concrete mix or Jesmonite, tap the sides for a minute to raise the air, and strike the bottom flat.
Demold after a day, sand the bottom flat, seal the dish and stick on felt pads so it does not scratch the table.
Print details
| Cast material | Concrete |
|---|---|
| Printed parts | 5 |
| Size (W x D x H) | 128 x 128 x 60 mm |
| Print bed needed | 151 x 128 mm, 60 mm tall |
| Filament | ~214 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Not needed |
| Download | ZIP: 5 printed parts (STL) + dish master (STL) + print sheet + recipe |
| Added | 2026-09-25 |
Made with the free Silicone mold maker generator. Upload your own model and get the same kind of mold built around it, in your browser.
Free download. Opens the Thingiverse listing in a new tab.
Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.
New to casting? Read the silicone mold maker guide.
Mix Jesmonite or a white cement with small chips of coloured, already cured Jesmonite or crushed stone, fill the mold, and let it cure. Then sand the rim and the inside with wet paper, working down to 400 grit, until the chips show through as flat spots.
Not on its own: concrete and Jesmonite are porous. Seal the dish with a clear concrete sealer or a food-safe wax before you use it for a soap bar or a damp sponge, and let it dry for a day after sealing.
In box mode the silicone is poured over the master, so it fills the dish's well as it rises. When you flip the cured block, the only opening left is where the dish stood on the base: its bottom. You fill it there and strike that face flat.
Concrete
A round concrete tabletop fire bowl, 110 mm across, with a pocket for a standard gel fuel can. A silicone mold kit from printed parts.
Concrete
A square concrete bud vase with a glass test tube inside, 50 x 50 x 120 mm. A silicone mold kit from printed parts.
Concrete
A concrete card holder shaped like a little staircase, with a slot for a business card, postcard or photo on the top step.
Concrete
A broken-open concrete sphere, 120 mm across, as a three-wick candle vessel. A silicone mold kit from printed parts.
Concrete
An architectural concrete desk organizer: pen holes, a phone slot and a spiral staircase winding down its end.
Concrete
An 80 mm lava stone look incense sphere in concrete, pitted all over, with a well on top for a cone. A silicone mold kit from printed parts.
Concrete
Four mini concrete succulent pots, oval, round, hexagon and square, each with a drainage hole, cast straight in one printed tray.
Concrete
Two 90 mm concrete incense holder discs, one plain and one with a gear edge, each with a raised stick holder, cast in one printed tray.