◆ Concrete
Snowflake concrete coaster tray mold
Four snowflake coasters cast in concrete straight into a printed tray. A Christmas set, no silicone.
◆ Concrete
Four snowflake coasters cast in concrete straight into a printed tray. A Christmas set, no silicone.
A printed tray for four round coasters, each 95 mm across and 10 mm thick, with a six-armed snowflake engraved in the face: every arm carries three pairs of branches round a small hexagon, and a thin ring frames the flake. A plain band runs round the edge and the face is flat, so a mug still sits level.
Made with our tray mold generator in its rigid tray mode: print the tray, wipe in release and pour concrete, Jesmonite or plaster straight in, no silicone at all. Every groove has sloped sides, so the coaster lifts out of the rigid tray with the snowflake crisp.
A winter set that stays out from December to February: rub white or silver paint into the grooves on a grey coaster, or leave white Jesmonite plain. The zip carries the tray exactly as the tool exported it, one coaster on its own as an STL, the master uploaded to the tool, and a print and pour sheet with the volume of each cavity.
Shown as a 3D render of the printed tray with three concrete coasters, not a photo.
Print the tray as exported, cavities up, no supports. PLA is fine.
Wipe a thin film of mold release or cooking oil into every cavity, including the grooves.
Mix a fine concrete or Jesmonite to a thick pour, fill each cavity, and vibrate it out: tap the tray on the table or hold a sander against the side for a minute until no more bubbles rise.
Cover the tray and let it cure for 24 hours, then flex the tray and tip the pieces out. Sand the back flat, and seal them once they have dried for a few days.
Print details
| Cast material | Concrete |
|---|---|
| Printed parts | 1 |
| Size (W x D x H) | 209 x 209 x 16 mm |
| Print bed needed | 209 x 209 mm, 17 mm tall |
| Filament | ~225 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Not needed |
| Download | ZIP: printed tray (STL) + one coaster (STL) + tool master (STL) + print and pour sheet |
| Added | 2026-09-30 |
Made with the free Tray mold generator. Upload your own model and get the same kind of mold built around it, in your browser.
Free download. Opens the Thingiverse listing in a new tab.
Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.
New to casting? Read the ice cube tray mold guide.
Seal the coaster once and let it dry, then brush thinned white or silver acrylic over the face and wipe the flat with a damp rag straight away. The paint stays in the grooves, and the sealer underneath stops it staining the flat. Seal again over the top.
Yes, they are a popular one. Glue cork or felt pads to the back, seal them well, and stack four with a ribbon round them. Cast them at least a week before you wrap them, so the concrete has dried and does not mark the packaging.
Usually a missed spot of release in the fine branches of the flake. Brush the release into every groove with a soft brush rather than wiping it on, and demold after a full day. Flex the tray corners first so air gets under the coaster before you tip it out.
Concrete
A round concrete tabletop fire bowl, 110 mm across, with a pocket for a standard gel fuel can. A silicone mold kit from printed parts.
Concrete
A square concrete bud vase with a glass test tube inside, 50 x 50 x 120 mm. A silicone mold kit from printed parts.
Concrete
A concrete card holder shaped like a little staircase, with a slot for a business card, postcard or photo on the top step.
Concrete
A broken-open concrete sphere, 120 mm across, as a three-wick candle vessel. A silicone mold kit from printed parts.
Concrete
An architectural concrete desk organizer: pen holes, a phone slot and a spiral staircase winding down its end.
Concrete
An 80 mm lava stone look incense sphere in concrete, pitted all over, with a well on top for a cone. A silicone mold kit from printed parts.
Concrete
Four mini concrete succulent pots, oval, round, hexagon and square, each with a drainage hole, cast straight in one printed tray.
Concrete
Two 90 mm concrete incense holder discs, one plain and one with a gear edge, each with a raised stick holder, cast in one printed tray.