◆ Cookie dough

Thanksgiving cookie cutter set with stamps

Five Thanksgiving cookie cutters with stamps: turkey, slice of pie, acorn, oak leaf and pumpkin.

Make your own cookie cutter
3D render of five 3D-printed Thanksgiving cookie cutters with their stamps and a golden stamped cookie in front of each: turkey, slice of pie, acorn, oak leaf and pumpkin
Cookie dough ~93 g Pro early access

Five autumn shapes for the Thanksgiving table: a turkey with its tail fanned out, a slice of pie with a crimped crust and a swirl of cream, an acorn with a scaled cap, an oak leaf with its veins and a ribbed pumpkin with a leaf. Every cutter has a stamp that presses the feathers, crust, veins or ribs into the cookie. Good for Thanksgiving dinner, Friendsgiving, place cards, autumn bake sales and harvest parties.

Read more

All five were made with our free cookie cutter generator, not modelled by hand: we drew each shape with its stamp's lines inside it and uploaded it with Generate stamp switched on. The zip holds exactly what the tool gives you, one STL per shape with the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and its stamp side by side, plus each drawing as an SVG. The cookies come out 90 x 87 mm (turkey), 85 x 74 mm (slice of pie), 69 x 80 mm (acorn), 65 x 90 mm (oak leaf) and 85 x 71 mm (pumpkin).

Bake the leaves and acorns from a spiced dough (cinnamon, ginger and a little molasses) and brush them with an egg wash before baking: the pressed veins and scales come out darker and the cookies look like real autumn leaves.

The cutters and stamps print flat with no supports, in PLA or PETG. A cutter touches dough for a minute, but a 3D print has fine layer grooves where crumbs can sit: pick a food-contact filament if you can, wash each part by hand in warm soapy water before and after use, never in a dishwasher, and flour the blade and stamp before every press.

Shown as a 3D render of the five printed cutters, their stamps and a stamped cookie from each, not a photo.

Thanksgiving cookie cutter set with stamps at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutters and the stamps, and baking paper
  • About 93 g of PLA or PETG for the whole set, ideally a food-contact filament

How to use it

7

  1. Print each file as exported: the cutter rim flat on the bed with the blade pointing up, and its stamp beside it, no supports.

  2. Wash every part in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip a cutter's blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust its stamp, press it into each cookie that cutter cut, about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash the parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

10 h 5 minPrint time
~93 gFilament
10Printed parts
All print details
Print details
Works withCookie dough
Printed parts10
Print bed needed204 x 98 mm, 14 mm tall
Filament~93 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: five cutters with their stamps (5 STL) + print and food-contact sheet + drawings (SVG) + README
Added2026-09-27

Pro early access until October 27, 2026, then free with any account.

Like it or post your print on Thingiverse

Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the cutter guide.

thanksgiving cookie cutter setthanksgiving cookie cuttersturkey cookie cutterfall cookie cuttersautumn cookie cutter set

Questions about this design

What is in the Thanksgiving cookie cutter set?

Five cutters, each with a matching stamp: a turkey, a slice of pie, an acorn, an oak leaf and a pumpkin. The stamps press the feathers, the crust and cream, the cap, the leaf veins and the pumpkin ribs into the cut cookies.

Can I use the Thanksgiving cookie cutters as place cards?

Yes. Bake the leaves or turkeys, flood them in one colour and write each guest's name across the middle once the icing is dry. Stand them against a glass or lay one on each plate; they double as a small dessert.

Do the Thanksgiving cookie cutters work on pie crust?

They do: cut leaves, acorns and pumpkins from rolled pie dough, press the stamp in lightly, brush with egg and lay them round the rim or over the top of a pie. Chill them first so the pressed lines survive the oven.

Can I make the cutters in the Thanksgiving cookie cutter set bigger or smaller?

Yes. Every drawing is in the zip as an SVG: upload one to the free cookie cutter generator, switch on Generate stamp and move the Cutter size slider (these are 80 to 90 mm). The stamp scales with its cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →