◆ Cookie dough

Winter cookie cutter set with stamps

Five winter cookie cutters with stamps: snowman, mitten, beanie hat, mug of cocoa and snowflake.

Make your own cookie cutter
3D render of five 3D-printed winter cookie cutters with their stamps and a golden stamped cookie in front of each: snowman, mitten, beanie hat, mug of cocoa and snowflake
Cookie dough ~101 g Pro early access

Five cosy winter shapes that work from the first frost to February: a snowman with a top hat and scarf, a mitten with a ribbed cuff, a knitted beanie with a pompom, a mug of hot cocoa with marshmallows and a six-arm snowflake. Every cutter has a stamp that presses the knit, the face, the heart or the snowflake lines into the cookie. Good for winter birthdays, Christmas and New Year cookie boxes, ski trips, hot chocolate bars and snow days.

Read more

All five were made with our free cookie cutter generator, not modelled by hand: we drew each shape with its stamp's lines inside it and uploaded it with Generate stamp switched on. The zip holds exactly what the tool gives you, one STL per shape with the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and its stamp side by side, plus each drawing as an SVG. The cookies come out 41 x 90 mm (snowman), 65 x 85 mm (mitten), 85 x 83 mm (beanie hat), 84 x 85 mm (mug of cocoa) and 76 x 85 mm (snowflake).

None of these five says Christmas, so they carry on long after the tree comes down: bake them for January birthdays, a ski weekend or a hot chocolate bar, in blues, whites and silvers.

The cutters and stamps print flat with no supports, in PLA or PETG. A cutter touches dough for a minute, but a 3D print has fine layer grooves where crumbs can sit: pick a food-contact filament if you can, wash each part by hand in warm soapy water before and after use, never in a dishwasher, and flour the blade and stamp before every press.

Shown as a 3D render of the five printed cutters, their stamps and a stamped cookie from each, not a photo.

Winter cookie cutter set with stamps at a glance: every printed part with its size, print time, filament, print settings and the three steps to use it

What you need

4
  • Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder
  • A rolling pin, and two 5 to 6 mm guides for an even thickness
  • Flour or cornflour for dusting the cutters and the stamps, and baking paper
  • About 101 g of PLA or PETG for the whole set, ideally a food-contact filament

How to use it

7

  1. Print each file as exported: the cutter rim flat on the bed with the blade pointing up, and its stamp beside it, no supports.

  2. Wash every part in warm soapy water before the first use.

  3. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper.

  4. Dip a cutter's blade in flour, press straight down with your palm on the rim, and lift.

  5. Dust its stamp, press it into each cookie that cutter cut, about 2 mm deep, and lift it straight up.

  6. Chill the stamped cookies for ten minutes, then bake.

  7. Wash the parts by hand straight after use and let them dry. PLA softens in a dishwasher.

Print details

10 h 50 minPrint time
~101 gFilament
10Printed parts
All print details
Print details
Works withCookie dough
Printed parts10
Print bed needed194 x 98 mm, 14 mm tall
Filament~101 g
Layer height0.2 mm
Infill15%
SupportsNot needed
DownloadZIP: five cutters with their stamps (5 STL) + print and food-contact sheet + drawings (SVG) + README
Added2026-09-27

Pro early access until October 27, 2026, then free with any account.

Like it or post your print on Thingiverse

Make your own cookie cutter →

Made with the free Cookie cutter generator. Upload your own shape and get the same kind of tool built from it, in your browser.

Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.

New to casting? Read the cutter guide.

winter cookie cutter setwinter cookie cutterssnowman cookie cuttermitten cookie cuttersnowflake cookie cutter and stamp

Questions about this design

Which cutters are in the winter cookie cutter set?

A snowman, a mitten, a beanie hat, a mug of hot cocoa and a snowflake, each with a stamp that drops inside it. The stamps press the snowman's face and buttons, the cuffs and knit, the marshmallows and heart, and the snowflake's arms.

Is the winter cookie cutter set only for Christmas?

No, that is the point of it: none of the shapes is a Christmas symbol, so the same set works for New Year, January birthdays, snow days and ski trips. Ice them in blue and white instead of red and green.

How do I make the knit on the winter cookie cutter set's mitten and beanie stand out?

Flood the cookie and let the icing crust for an hour, then pipe thin lines of a second colour along the pressed ribbing, or brush the plain baked cookie with thinned food colouring and wipe the surface so the colour stays in the grooves.

Can I make the cutters in the winter cookie cutter set bigger or smaller?

Yes. Every drawing is in the zip as an SVG: upload one to the free cookie cutter generator, switch on Generate stamp and move the Cutter size slider (these are 85 to 90 mm). The stamp scales with its cutter, so its lines still fit the cookie.

More designs

See all cookie cutters →