◆ Candle wax
D20 candle mold
A 70 mm d20 candle with all twenty numbers engraved, the real die as a candle. Silicone mold kit.
◆ Candle wax
A 70 mm d20 candle with all twenty numbers engraved, the real die as a candle. Silicone mold kit.
A twenty-sided die candle 70 mm from face to face, with every number from 1 to 20 engraved in its faces like a real d20, and the 20 on top. It stands on its 1, so the natural 20 is what faces up on the table.
The mold is made with the hugging-shell mode of our silicone mold maker. Engraved numbers on every face lock any rigid mold, and silicone peels out of them. Print the base with the die fused onto it, the two shell halves and the six clamps, pour about 565 ml of silicone, and cast in the flexible mold that comes out.
Light it at the start of a session for luck, or cast a set in the party's colours as gifts. It looks best in a deep purple, red or a marbled pour, with a little gold mica rubbed into the numbers. The zip carries every printed part, the die master as its own STL, the tool's own print-settings sheet and a recipe file for the generator.
Shown as a 3D render of the printed mold parts pulled apart around the master, not a photo.
Print the base, which has the master already fused onto it, the two shell halves and the six clamps (all six are in clamps.stl). No supports.
Stand the shell halves on the base around the master and push the six printed clamps over the seams. Steel binder clips work too, the seats for them are built into the shell.
Tape the outside seams or run a bead of hot glue along them, because silicone finds every gap.
Mix 608 ml of silicone in one batch, pour it into the open top in a thin stream, and fill level with the rim.
Once it has cured, unclip the shell and slide each half off SIDEWAYS, not upward: the master is wider above its foot, so the base rib is left open for that. Then peel the silicone off the master. That silicone is your mold.
Set the silicone back in the shell to keep its shape, and cast into it through the opening the base left.
Before the first cast, cut a thin vent into the silicone from about 5 mm up the die toward the opening. The tool found about 1.8 ml of air that cannot rise out on its own there, and the vent lets it escape.
Print details
| Cast material | Candle wax |
|---|---|
| Printed parts | 9 |
| Size (W x D x H) | 121 x 134 x 84 mm |
| Print bed needed | 134 x 119 mm, 85 mm tall |
| Filament | ~278 g |
| Layer height | 0.2 mm |
| Infill | 15% |
| Supports | Not needed |
| Download | ZIP: 9 printed parts in 4 STL files + candle master (STL) + print sheet + recipe |
| Added | 2026-09-24 |
Pro early access until October 24, 2026, then free with any account.
Make your own silicone mold →Made with the free Silicone mold maker generator. Upload your own model and get the same kind of mold built around it, in your browser.
Free for personal use. Selling the pieces you cast needs a commercial licence (Pro or Founder); passing on the file itself is not permitted on any plan. Full terms.
New to casting? Read the silicone mold maker guide.
Through the centre of the 20 face, between the 2 and the 0. Pierce the silicone there with a wick needle and thread a primed wick through before you pour; the opening you pour into is the 1 face the die stands on.
The tool checks where air can get stuck while you pour, and on this die about 1.8 ml stays trapped about 5 mm up from the foot, where it cannot rise to the opening. One thin cut in the cured silicone from that spot to the opening lets it out, and every cast after that comes out with that face whole.
The numbers are engraved, so rub a little gold or silver mica into them with a fingertip once the candle is out of the mold, then buff the faces around them clean. On a dark wax it looks like a painted die.
Candle waxPro early access
A little sheet ghost with big eyes and an "o" mouth, 86 mm tall. A rigid two-part print for Halloween candles.
Candle waxPro early access
A sitting teddy bear with button eyes, a ribbon bow and its paws on its tummy. A rigid two-part print.
Candle waxPro early access
A traditional straw beehive with coiled bands, an arched entrance and a bee above the door. A rigid two-part print.
Candle waxPro early access
An 82 mm lotus flower candle, four rings of petals round a closed bud, as a silicone mold from a printed shell.
Candle waxPro early access
An 87 mm pine cone candle with 120 overlapping scales, as a silicone mold from a printed shell.
Candle waxPro early access
An 86 mm dragon egg candle covered in rows of overlapping scales, as a silicone mold from a printed shell.
Candle waxPro early access
Six maple leaf wax melts per pour, with the veins pressed in, from a silicone tray you make yourself.
Candle waxPro early access
Six plump pumpkin wax melts per pour, ribbed and with a little stem, from a silicone tray you make yourself.